| For the following pollutants
| Use the following span values for your CEMS
| Use the following performance specifications for your CEMS
| During each relative accuracy test run, use the following methods to collect concurrent data
|
|---|
| 1. Particulate Matter | | For operation and correlation test, P.S. 11 in appendix B of this part and procedure 2 of appendix F to this part | Follow the test methods in Table 5 to Subpart WWWW.
|
| | | For quarterly accuracy determinations, daily calibration drift tests, and each response correlation audit or relative response audit, procedure 2 of appendix F to this part.
| |
| 2. Nitrogen Oxides | Control device outlet: 125 percent of the maximum estimated hourly nitrogen oxides emissions of the municipal waste combustor | For operation, P.S. 2 in appendix B of this part and procedure 1 in appendix F of this part
For relative accuracy audit, P.S. 2 in appendix B of this part and procedure 1 of appendix F of this part | Method 7, 7A, 7C, 7D, or 7E in appendix A-4 to part 60 of this chapter.
|
| | | For quarterly accuracy determinations and daily calibration drift tests, procedure 1 in appendix F of this part
| |
| 3. Sulfur Dioxide | Control device outlet: 50 percent of the maximum estimated hourly sulfur dioxide emissions of the municipal waste combustor | For operation, P.S. 2 in appendix B of this part
For relative accuracy audit, P.S. 2 in appendix B of this part and procedure 1 of appendix F of this part | Method 6, 6A, or 6C, in appendix A-4 to part 60 of this chapter.
|
| | | For quarterly accuracy determinations and daily calibration drift tests, procedure 1 in appendix F of this part.
| |
| 4. Carbon Monoxide | 125 percent of the maximum estimated hourly carbon with monoxide emissions of the municipal waste combustor | For operation, P.S. 4A in appendix B of this part and procedure 1 of appendix F of this part
For relative accuracy audit, P.S. 4A in appendix B of this part and procedure 1 of appendix F of this part | Method 10, 10A, or 10B in appendix A-4 to part 60 of this chapter.
|
| | | For quarterly accuracy determinations and daily calibration drift tests, procedure 1 in appendix F of this part.
| |
| 5. Oxygen or Carbon Dioxide | 25 percent oxygen or 20 percent carbon dioxide | P.S. 3 in appendix B of this part | Method 3A or 3B in appendix A-2 to part 60 of this chapter, or, as an alternative for oxygen or carbon dioxide correction, the manual method portion of ASME PTC-19-10-1981—part 10.
|
| 6. Mercury | Follow the approved site-specific monitoring plan | For operation, P.S. 12A in appendix B of this part and procedure 5 of appendix F of this part or the approved site-specific monitoring plan | Follow the test methods in Table 5 to Subpart WWWW.
|
| | | For relative accuracy audit, daily calibration, weekly system integrity check, quarterly audit, procedure 5 of appendix F of this part
| |
| 7. Hydrogen chloride | Follow the approved site-specific monitoring plan | For operation, P.S. 18 in appendix B of this part and procedure 6 of appendix F of this part or the approved site-specific monitoring plan
For relative accuracy audit, daily calibration, quarterly audit, and other applicable quality assurance/quality control checks procedure 6 of appendix F of this part | Follow the test methods in Table 5 to Subpart WWWW, except you may also use Methods 320 or 321 of appendix A to part 63.
|
| 8. Cadmium or Lead | Follow the approved site-specific monitoring plan | For operation, the approved site-specific monitoring plan | Follow the test methods in Table 5 to Subpart WWWW. |