OT:RR:NC:N1:102
occur is whether an article emerges from a process with a new name, character, or use different from that possessed by the article prior to processing. See Texas Instruments Inc. v. United States, 681 F.2d 778 (C.C.P.A. 1982). This determination is based on the totality of the evidence. See National Hand Tool Corp. v. United States, 16 C.I.T. 308 (1992), aff’d, 989 F.2d 1201 (Fed. Cir. 1993). Additionally, Section 304 of the Tariff Act of 1930, as amended (19 U.S.C. 1304), provides that unless excepted, every article of foreign origin imported into the United States shall be marked in a conspicuous place as legibly, indelibly, and permanently as the nature of the article (or its container) will permit, in such a manner as to indicate to the ultimate purchaser in the United States, the English name of the country of origin of the article. Congressional intent in enacting 19 U.S.C. 1304 was “that the ultimate purchaser should be able to know by an inspection of the marking on the imported goods the country of which the goods is the product. The evident purpose is to mark the goods so that at the time of purchase the ultimate purchaser may, by knowing where the goods were produced, be able to buy or refuse to buy them, if such marking should influence his will.” See United States v. Friedlander & Co., 27 C.C.P.A. 297, 302 (1940). Part 134 of the U.S. Customs and Border Protection (CBP) Regulations (19 CFR 134) implements the country of origin marking requirements and exceptions of 19 U.S.C. 1304. Section 134.1(b), CBP Regulations (19 CFR 134.1(b)), defines “country of origin” as the country of manufacture, production, or growth of any article of foreign origin entering the United States. Further work or material added to an article in another country must effect a substantial transformation in order to render such other country the “country of origin” within the meaning of the marking laws and regulations. CBP has held that whether a manufacturing process is sufficiently complex to rise to the level of a substantial transformation is determined upon consideration of all the operations that occur within that country. Here, the final assembly processes are rather simple and do not constitute a substantial transformation. Inserting and pressing components into a housing does not change the shape, character, or predetermined use of the inputs. Instead, we look to the origin of the housing to determine the origin of the fluid end, as it is the essential component of the product. It contributes to the pressurization process, encases the internal components, and accounts for approximately 90 percent of the finished product’s value. Therefore, as the origin of the housing is the UAE, the country of origin of the fluid ends (three-cylinder and five-cylinder models) is the UAE. The holding set forth above applies only to the specific factual situation and merchandise description as identified in the ruling request. This position is clearly set forth in Title 19, Code of Federal Regulations (CFR), Section 177.9(b)(1). This section states that a ruling letter is issued on the assumption that all of the information furnished in the ruling letter, whether directly, by reference, or by implication, is accurate and complete in every material respect. In the event that the facts are modified in any way, or if the goods do not conform to these facts at time of importation, you should bring this to the attention of U.S. Customs and Border Protection (CBP) and submit a request for a new ruling in accordance with 19 CFR 177.2. Additionally, we note that the material facts described in the foregoing ruling may be subject to periodic verification by CBP. This ruling is being issued under the provisions of Part 177 of the Customs and Border Protection Regulations (19 C.F.R. 177).
A copy of the ruling or the control number indicated above should be provided with the entry documents filed at the time this merchandise is imported. If you have any questions regarding the ruling, please contact National Import Specialist Sandra Martinez at [email protected].
Sincerely,
(for) Denise Faingar Designated Official Performing the Duties of the Division Director National Commodity Specialist Division